Energy
O. E. Olabode; I. K. Okakwu; D. O. Akinyele; T. O. Ajewole; S. Oyelami; O. V. Olisa
Abstract
The impact of solar radiation and ambient temperature on solar PV energy yield and its corresponding economic implication was investigated. The electrical load assessment was done by physical inspection through periodic visits to study location. Five different scenarios were investigated for two locations ...
Read More
The impact of solar radiation and ambient temperature on solar PV energy yield and its corresponding economic implication was investigated. The electrical load assessment was done by physical inspection through periodic visits to study location. Five different scenarios were investigated for two locations - Ogun and Bayelsa States: Case I considers the PV performance based on the locations’ historical solar radiation and temperature data, Case II considers 30 % increase in the solar radiation data while the ambient temperature data remains fixed, Case III focuses on when solar radiation data is decreased by 30 % while the ambient temperature data remains constant, Case IV considers the solar radiation data remains constant while the temperature values are increased by 30 %, and Case V examined the same solar radiation values with temperature data values being decreased by 30 %. The HOMER pro was used as the implementation tool, Electrical energy yield, Unmet electric load, Net present cost, Levelized cost, and Operating cost for Cases I, II, III, IV, and V in Ota, Ogun State were as follows: 28,659 kWh/y, 4.71kWh/y, $13,537, $0.166, 271.43kWh/y; 37,260 kWh/y, 1.63kWh/y, $12,417, $0.152, 290.43kWh/y; 20,058kWh/y, 3.22kWh/y, $15,663, $0.192, 293.14kWh/y; 28,659kWh/y, 4.71kWh/y, $13,537, $0.166, 271.43kWh/y; and 28,659kWh/y, 4.61kWh/y, $13,437, $0.156, 261.43kWh/y, respectively while similar trend was observed for Otuasega in Bayelsa State. The results of the analysis showed that the optimal performance of the PV module occurred at a higher solar radiation and a lower ambient temperature.
Energy
M. Esmaeili Shayan; G. Najafi; B. Ghobadian; S. Gorjian
Abstract
Photovoltaic cells are a significant renewable energy source due to their cheap cost and renewability. In both warm sunny and colder and cloudier conditions, a-Si modules outperform c-Si modules on a normalized energy basis. This study investigated 1 m2 of amorphous photovoltaic silicon on curved surfaces. ...
Read More
Photovoltaic cells are a significant renewable energy source due to their cheap cost and renewability. In both warm sunny and colder and cloudier conditions, a-Si modules outperform c-Si modules on a normalized energy basis. This study investigated 1 m2 of amorphous photovoltaic silicon on curved surfaces. The Taguchi and response surface methods were utilized to expand the model in real terms. Results demonstrated the technology gap in the use of silicon crystal photovoltaics is eliminated. The maximum power in the Taguchi method test is 59.87 W, while the minimum power is 57.84 W when the system is deployed on a flat surface, and the maximum power in the RSM Test is 61.14 W when the system is deployed on a hemispherical surface, and the minimum power is 56.6 W when the system is deployed on a flat surface. The minimal performance was 7.1% on a level surface. The flat surface produced 810 kWh, the cylindrical surface 960 kWh, and the hemisphere 1000 kWh. The NPV at Flat surface is $697.52, with a 34.81%, IRR and an 8.58-year capital return period. Hemisphere and cylindrical surfaces both get $955.18. The investment yield was 39.29% for cylindrical constructions and 40.47% for hemispheres. On the flat surface, doubling fixed investment improved IRR by 21.3%. The cylindrical system increased by 25.59% and the hemisphere by 24.58%. The developed simulation model is empirically evaluated using a MATLAB computer tool; the key findings from the validation procedure are reported in this study.
